key features miniature dip package 3.0 kvdc isolation 2w output power single & dual outputs 3.6 mh mtbf low cost electrical speci? cations speci? cations typical @ +25 1 c with nominal input voltage & rated output current, unless otherwise noted. speci? cations subject to change without notice. micropower direct compact minidip, 2w high isolation dc/dc converters g200i series micropower direct tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com web: www/micropowerdirect.com input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 24 vdc input 21.6 24.0 26.4 48 vdc input 43.2 48.0 52.8 input filter internal capacitor reverse polarity input current 0.3 a output parameter conditions min. typ. max. units output voltage accuracy ! 1.0 ! 3.0 % output voltage balance dual output , balanced loads ! 0.1 ! 1.0 % line regulation for vin change of 1% ! 1.2 ! 1.5 % load regulation see model selection guide ripple & noise (20 mhz) 100 150 mv p - p ripple & noise (20 mhz) over line, load & temp. 200 mv p - p ripple & noise (20 mhz) 5 mv rms output power protection 120 % temperature coef? cient ! 0.01 ! 0.02 %/ 1 c output short circuit momentary (0.5 sec.) general parameter conditions min. typ. max. units isolation voltage 60 seconds 3,000 vdc isolation resistance 500 vdc 1,000 m ? isolation capacitance 100 khz, 1v 80 120 pf switching frequency 50 80 100 khz environmental parameter conditions min. typ. max. units operating temperature range -40 +25 +70 1 c storage temperature range -40 +125 1 c cooling free air convection humidity rh, non-condensing 95 % physical case size, 5v, 12v & 24v input models 0.80 x 0.40 x 0.27 inches (20.32 x 10.16 x 6.85 mm) case size, 48vdc input models 0.80 x 0.40 x 0.30 inches (20.32 x 10.16 x 7.50 mm) case material non-conductive black plastic weight 0.09 oz (2.7g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25 1 c, gnd benign 3.6 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 9.0 vdc 12 vdc input -0.7 18.0 24 vdc input -0.7 30.0 48 vdc input -0.7 55.0 internal power dissipation all models 650 mw caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings.
notes: all dimensions are typical in inches (mm) tolerance x.xx = ! 0.01 ( ! 0.25) pin 1 is marked by a dot or indentation on the top of the unit model number input output load regulation (%, max) ef? ciency (%, typ) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load g201i 5 4.5 - 5.5 452 35 3.3 500.0 10.0 11 73 1,000 g202i 5 4.5 - 5.5 526 35 5.0 400.0 8.0 11 76 1,000 g203i 5 4.5 - 5.5 495 35 12.0 165.0 3.0 7 80 1,000 g204i 5 4.5 - 5.5 499 35 15.0 133.0 2.5 7 80 1,000 g205i 5 4.5 - 5.5 519 35 ! 5.0 ! 200.0 ! 4.0 10 77 1,000 g206i 5 4.5 - 5.5 504 35 ! 12.0 ! 83.0 ! 1.5 7 79 1,000 g207i 5 4.5 - 5.5 501 35 ! 15.0 ! 66.0 ! 1.0 7 79 1,000 g211i 12 10.8 - 13.2 185 25 3.3 500.0 10.0 8 74 500 g212i 12 10.8 - 13.2 212 25 5.0 400.0 8.0 8 78 500 g213i 12 10.8 - 13.2 200 25 12.0 165.0 3.0 5 82 500 g214i 12 10.8 - 13.2 200 25 15.0 133.0 2.5 5 83 500 g215i 12 10.8 - 13.2 222 25 ! 5.0 ! 200.0 ! 4.0 875500 g216i 12 10.8 - 13.2 201 25 ! 12.0 ! 83.0 ! 1.5 582500 g217i 12 10.8 - 13.2 200 25 ! 15.0 ! 66.0 ! 1.0 582500 g221i 24 21.6 - 26.4 92 10 3.3 500.0 10.0 8 74 200 g222i 24 21.6 - 26.4 108 10 5.0 400.0 8.0 8 77 200 g223i 24 21.6 - 26.4 101 10 12.0 165.0 3.0 5 81 200 g224i 24 21.6 - 26.4 101 10 15.0 133.0 2.5 5 82 200 g225i 24 21.6 - 26.4 111 10 ! 5.0 ! 200.0 ! 4.0 875200 g226i 24 21.6 - 26.4 102 10 ! 12.0 ! 83.0 ! 1.5 581200 g227i 24 21.6 - 26.4 100 10 ! 15.0 ! 66.0 ! 1.0 582200 G231I 48 43.2 - 54.8 28 6 3.3 500.0 10.0 8 74 100 g232i 48 43.2 - 54.8 27 6 5.0 400.0 8.0 8 77 100 g233i 48 43.2 - 54.8 26 6 12.0 165.0 3.0 5 81 100 g234i 48 43.2 - 54.8 25 6 15.0 133.0 2.5 5 82 100 g235i 48 43.2 - 54.8 28 6 ! 5.0 ! 200.0 ! 4.0 875100 g236i 48 43.2 - 54.8 26 6 ! 12.0 ! 83.0 ! 1.5 581100 g237i 48 43.2 - 54.8 25 6 ! 15.0 ! 66.0 ! 1.0 582100 232 tosca drive, stoughton, ma 02072 www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481 mechanical dimensions micropower direct pin single dual 1 -vin -vin 7nc nc 8 +vout +vout 9 no pin common 10 -vout -vout 14 +vin +vin nc = no connection pin connections single output f max dual output f max 470 ! 390 capacitive load model selection guide notes: 1. dual output units may be connected to provide a 10v, 24v or 30 vdc output. to do this, connect the load across the positive (+vout) and negative (-vout) outputs and ? oat the output common. 2. these units do not require external components to operate, but the use of an input capacitor (10 f) may enhance performance in some applications. an output capacitor (4.7 f to 10 f) may be used to reduce ripple. derating curve ambient temperature 1 c 85 -40 -20 0 5 15 25 35 45 55 65 75 95 105 0 20 40 60 80 100 output power % 0.80 (20.32) 10 9 1 14 0.10 (2.54) 0.60 (15.24) 0.10 (2.5) 0.01 (0.25) 0.01 (0.25) 0.40 (10.2) 0.12 (3.05) 0.05 (1.25) bottom side 7 8 note: t = 0.27 (6.85) for 5, 12 & 24 vdc input models 0.30 (7.50) for 48 vdc input models t
|
